I bought an argon flowmeter, but I'm using nitrogen. I know there's a density difference in the gases, and saw people saying I'd need to set it higher to get the proper l/min with nitrogen. Shouldn't I need to set the argon meter lower since nitrogen is less dense and will interact less with the ball? It's a matter of ~21 l/min or 13 l/min on the argon. I just don't want to set it too high and waste all of my nitrogen brain damaging me.
-
Hey Guest,
If you would still like to donate, you still can. We have more than enough funds to cover operating expenses for quite a while, so don't worry about donating if you aren't able. If you want to donate something other than what is listed, you can contact RainAndSadness.
Bitcoin Address (BTC): 39deg9i6Zp1GdrwyKkqZU6rAbsEspvLBJt
Ethereum (ETH): 0xd799aF8E2e5cEd14cdb344e6D6A9f18011B79BE9
Monero (XMR): 49tuJbzxwVPUhhDjzz6H222Kh8baKe6rDEsXgE617DVS
DD8UKNaXvKNU8dEVRTAFH9Av8gKkn4jDzVGF25snJgNfUfKKNC8
limeoctave
welcome home old friend, how was your life?
- Mar 24, 2024
- 226
Exit bag and inert gas megathread
You can use an argon regulator (with flowmeter) on a nitrogen cylinder if the cylinder connection for nitrogen in your region is the same as an argon cylinder connection. ... You seem like you've done a lot of research. Do you know if a US (CGA580 flowmeter connection [like this one]) works...
sanctioned-suicide.net
Thank you.Exit bag and inert gas megathread
You can use an argon regulator (with flowmeter) on a nitrogen cylinder if the cylinder connection for nitrogen in your region is the same as an argon cylinder connection. ... You seem like you've done a lot of research. Do you know if a US (CGA580 flowmeter connection [like this one]) works...
I'm looking for the same answer so I ran a test nusing half a tank of Nitrogen which initially contained 2 litres of gas at 200 bar
Given that the tank had initially contained 400 Liters of Nitrogen gas and was now at a reading of 100 Bar i am assuming that I had 200 Liters of gas remaining.
After setting the regulator to 10 LPM it took 6 mins for the regulator to reach the tank 50 Bar mark at which point the flow meter had gone from 10 LPM to 11 LMP so i readjusted the flow meter to give a reading of 10 LPM and the gas flowed for another 6 mins before the flow rate began to slow down.
This would mean that using a 10 LPM / 11 LPM reading. That 200 Liters of Nitrogen took 12 minutes to deplete.
This would mean that the true flow rate was actually 16 LPM and not 10 LPM.
Given that the tank had initially contained 400 Liters of Nitrogen gas and was now at a reading of 100 Bar i am assuming that I had 200 Liters of gas remaining.
After setting the regulator to 10 LPM it took 6 mins for the regulator to reach the tank 50 Bar mark at which point the flow meter had gone from 10 LPM to 11 LMP so i readjusted the flow meter to give a reading of 10 LPM and the gas flowed for another 6 mins before the flow rate began to slow down.
This would mean that using a 10 LPM / 11 LPM reading. That 200 Liters of Nitrogen took 12 minutes to deplete.
This would mean that the true flow rate was actually 16 LPM and not 10 LPM.
Similar threads
- beardyoldcorpse
- Suicide Discussion
Suicide Discussion
beardyoldcorpse
Suicide Discussion
Blockz
- heavenplzhelp77
- Suicide Discussion 2