Inert bag method making sure I have my ducks in a row

[hellocana]

I'm planning on doing this method in the next month, I would do it sooner if my license wasn't suspended lol. Just looking to make sure I have everything in order. I'm also planning on going in one go at a hotel. I can't really do testing ahead of time but if anything I can do testing right before or pass on the testing all together. I've hyperlinked the products below

Tank:
I can get a nitrogen tank which measures to 24 inches. Based on what I'm seeing, that should be more than the 600L required. It's the 11AL on the chart below and %99.9+ nitrogen according to safety data sheet. Just to make sure is the tank big enough?


Tank Items:

Harris flow meter regulator. This is for Argon, but for conversion for nitrogen flow should be 26 CFT. Is this correct?
Nut and nipple Nut is 5/8" and Nipple is for 1/4" rose. Question: does the nipple screw in to the nut by the threading?
Flexbible PVC tubing 1/4" it says soft water tube, should that be okay?
Tube cutter to shorten the tube
Hose clamp to tighten around the nipple
Wrench to tighten the bolts



Bag:

Reynolds oven bag : Measures 19 x 23 inches
Elastic cord and cord lock to go tighten the bag
Scissors to cut the cord
Micropourose surgical tape on top part of bag and to seal bottom



Thick oven gloves to protect my hands, safety strap to keep cylinder in place

Any insights would be appreciated!

 

[SomewhereAlongThe]

I got the 11 AL and it was 55 scf which was 1.53m3 in volume which is 1,530 Liters weighing 22.6 pounds, which is more than enough.

As for the nitrogen conversion with the argon I reference this post https://www.sanctioned-suicide.net/...ert-gas-megathread.8393/page-176#post-2711877

No the nipple doesn't screw it, it just rests in the nut, a perfect fit. Make sure you also test this part of your setup for leaks with soapy water. (I use dish soap, some use windex)

As for your tubing, I used a similar if not the exact same hose with 10mm OD and it left a big gap that when I tested it on my dummy head, didn't inflate the bag well.

However I got oxygen tubing, and it did inflate the bag well, and didn't leave a huge gap. So I recommend oxygen tubing.

I recommend these turkey bags: https://www.amazon.ca/dp/B075BQYDFV?ref=ppx_yo2ov_dt_b_fed_asin_title
Also confirm the size of the exit bag, a little big isn't a huge deal but too small won't work.

 

[hellocana]

I got the 11 AL and it was 55 scf which was 1.53m3 in volume which is 1,530 Liters weighing 22.6 pounds, which is more than enough.

As for the nitrogen conversion with the argon I reference this post https://www.sanctioned-suicide.net/...ert-gas-megathread.8393/page-176#post-2711877

No the nipple doesn't screw it, it just rests in the nut, a perfect fit. Make sure you also test this part of your setup for leaks with soapy water. (I use dish soap, some use windex)

As for your tubing, I used a similar if not the exact same hose with 10mm OD and it left a big gap that when I tested it on my dummy head, didn't inflate the bag well.

However I got oxygen tubing, and it did inflate the bag well, and didn't leave a huge gap. So I recommend oxygen tubing.

I recommend these turkey bags: https://www.amazon.ca/dp/B075BQYDFV?ref=ppx_yo2ov_dt_b_fed_asin_title
Also confirm the size of the exit bag, a little big isn't a huge deal but too small won't work.

Thanks for the response! If the nipple doesnt screw in wouldn't it just blow out?

 

[hellocana]

I got the 11 AL and it was 55 scf which was 1.53m3 in volume which is 1,530 Liters weighing 22.6 pounds, which is more than enough.

As for the nitrogen conversion with the argon I reference this post https://www.sanctioned-suicide.net/...ert-gas-megathread.8393/page-176#post-2711877

No the nipple doesn't screw it, it just rests in the nut, a perfect fit. Make sure you also test this part of your setup for leaks with soapy water. (I use dish soap, some use windex)

As for your tubing, I used a similar if not the exact same hose with 10mm OD and it left a big gap that when I tested it on my dummy head, didn't inflate the bag well.

However I got oxygen tubing, and it did inflate the bag well, and didn't leave a huge gap. So I recommend oxygen tubing.

I recommend these turkey bags: https://www.amazon.ca/dp/B075BQYDFV?ref=ppx_yo2ov_dt_b_fed_asin_title
Also confirm the size of the exit bag, a little big isn't a huge deal but too small won't work.

Couple other questions:

I can't seem to find out the size of the oxygen tubing, looks like it's all one size. Are you supposed to cut off the end tips and just use the tubing or can those ends fit on the nipple?
According to the nut and nipple, I'm seeing that it says "max 200 PSI".. will that not work? Since i assume the PSI is going way higher than that
And would those two products fit each other? The regulator and nut/nipple, there is no size indication on the description of the regulator, I just see that they're "frequently bought together"